New HelvePic32 using the PIC32MX270f256D chip with more memory and GPIO pins. The board comes fully assembled and ready to use!

Technical Details:

• PIC32MX270F256D Mikrocontroller
• 256kB Flash
• 64kB RAM
• 40MHz Clock
• Socket for ESP-01 ESP8266 WiFi module
• USB 2.0 port for programming (USB mini)
• 2x UART, I2C, SPI - UART on dedicated pins, I2C on dedicated pins
  
• 5 external Interrupts
• 29 I/O Pins - 8 GPIO pins aligned with 3.3V and GND for easy sensor and servo connection
  
• 9-channel 10-bit ADC
• PWM on each pin
• chipKIT Bootloader pre-installed
• All pins are on a 0.1" grid, leaving one connector row on each side with a standard breadboard
• 2 selectable user LED
  
• simple code upload from UECIDE or MPIDE

Breadboard version of the HelvePic32.

Fully assembled - easy for beginners. Comes with Headers (female and male) that you can chose to solder at your convenience

Technical Details:

• PIC32MX250F128B Mikrocontroller
• 128kB Flash
• 32kB RAM
• 40MHz Clock
• USB 2.0 port for programming (USB mini)
• 2x UART, I2C, SPI
• 5 external Interrupts
• 15 I/O Pins
• 9-channel 10-bit ADC
• PWM on each pin
• chipKIT DP32 Bootloader pre-installed
• All pins are on a 0.1" grid, leaving one connector row on each side with a standard breadboard
• 1 LED for 3.3V
• simple code upload from UECIDE or MPIDE

Kit for soldering a HelvePic32.

Includes PCB and all parts - no SMD, all parts are through-hole - easy for beginners

Technical Details:

• PIC32MX250F128B Mikrocontroller
• 128kB Flash
• 32kB RAM
• 40MHz Clock
• USB 2.0 port for programming (USB mini)
  
• 2x UART, I2C, SPI
• 5 external Interrupts
• 21 I/O Pins
• 9-channel 10-bit ADC
• PWM on each pin
  
• Simple replacement of DIL chip
• chipKIT DP32 Bootloader pre-installed
• All pins are on a 0.1" grid, so  0.1" protoboards can be used
  
• 3 LED for 5V,  3.3V and user-defined
  
• simple code upload from UECIDE or MPIDE
• Pull-up resistors for I2C selectable via jumper
  
• external pins for UART1, UART2 and I2C

HelvePic32 kit soldered and tested. For those who do not want to solder the kit by themselves.

The board is soldered by hand by ourselves and tested for upload and function of the pins. The soldering will be done once ordered, so please accept 3-5 days for delivery

Technical Details:

• PIC32MX250F128B Mikrocontroller
• 128kB Flash
• 32kB RAM
• 40MHz Clock
• USB 2.0 port for programming (USB mini)
  
• 2x UART, I2C, SPI
• 5 external Interrupts
• 21 I/O Pins
• 9-channel 10-bit ADC
• PWM on each pin
  
• Simple replacement of DIL chip
• chipKIT DP32 Bootloader pre-installed
• All pins are on a 0.1" grid, so  0.1" protoboards can be used
  
• 3 LED for 5V,  3.3V and user-defined
  
• simple code upload from UECIDE or MPIDE
• Pull-up resistors for I2C selectable via jumper
  
• external pins for UART1, UART2 and I2C